R5F100GEAFB#10
Likaroloana
Theknoloji ea tšebeliso ea matla e tlase haholo
VDD = motlakase o le mong oa motlakase oa 1.6 ho isa ho 5.5 V
Mokhoa oa HALT
EMA mokhoa
SNOOZE mode
RL78 CPU ea mantlha
Mehaho ea CISC e nang le liphaephe tsa mekhahlelo e 3
Nako e fokolang ea ho phethahatsa litaelo: E ka fetoloa
ho tloha ka lebelo le phahameng (0.03125 μs: @ 32 MHz ts'ebetso
ka high-speed on-chip oscillator) ho isa lebelong le tlase haholo
(30.5 μs: @ 32.768 kHz ts'ebetso e nang le sistimi e nyane
oache)
Sebaka sa liaterese: 1 MB
Lirekoto tsa morero o akaretsang: (8-bit register × 8) × 4
libanka
RAM ea on-chip: 2 ho isa ho 32 KB
memori ea khoutu ea flash
Khoutu ea Flash memory: 16 ho 512 KB
Boholo ba block: 1 KB
Thibelo ea ho hlakola le ho ngola hape (ts'ireletso
mosebetsi)
Ts'ebetso ea ho tlosa bothata ho on-chip
Ho iketsetsa mananeo (ka boot swap function/flash shield
mosebetsi oa fensetere)
Memori ea Flash ea data
Memori ea Flash ea data: 4 KB ho isa ho 8 KB
Tšebetso ea morao-rao (BGO): Litaelo li ka ba
e etsoa ho tsoa memoring ea lenaneo ha e ntse e ngola botjha faele
memori ea data flash.
Palo ea ba ngotseng hape: makhetlo a 1,000,000 (TYP.)
Matla a ho ngola hape: VDD = 1.8 ho 5.5 V
High-speed on-chip oscillator
Khetha ho tloha 32 MHz, 24 MHz, 16 MHz, 12 MHz, 8 MHz,
6 MHz, 4 MHz, 3 MHz, 2 MHz, le 1 MHz
Ho nepahala ho phahameng: +/- 1.0 % (VDD = 1.8 ho 5.5 V, TA = -20
ho ea ho +85°C)
Mocheso o sebetsang oa tikoloho
TA = -40 ho +85°C (A: Likopo tsa bareki, D:
Lisebelisoa tsa indasteri)
TA = -40 ho +105°C (G: Lisebelisoa tsa indasteri)
Tsamaiso ea matla le ts'ebetso ea ho tsosolosa
Potoloho ea on-chip power-on-reset (POR).
On-chip voltage detector (LVD) (Khetha ho sitisa le
tsosolosa ho tloha maemong a 14)
DMA (Direct Memory Access) controller · 2/4 channels · Palo ea lioache nakong ea phetisetso pakeng tsa 8/16-bit SFR le RAM e ka hare: 2 oache Multiplier le divider/multiply-accumulator · 16 bits × 16 bits = 32 bits (E sa ngolisoa kapa saennweng) · 32 bits ÷ 32 bits = 32 bits (E sa saenwang) · 16 bits × 16 bits + 32 bits = 32 bits (E sa saena kapa e saennoe) segokanyimmediamentsi sa sebolokigolo · CSI: dikanale tse 2 ho isa ho tse 8 · UART/UART (LIN-bese e tsheheditswe) : liteishene tse 2 ho isa ho tse 4 · Puisano ea I2C / Nolofalitsoeng ea I2C: 3 ho liteishene tsa 10 Timer · 16-bit timer: liteishene tse 8 ho isa ho tse 16 · 12-bit interval timer: 1 channel · Oache ea nako ea sebele: 1 channel (almanaka ea lilemo tse 99, ts'ebetso ea alamo, le ts'ebetso ea ho lokisa oache) · The Watchdog timer: 1 channel (e sebetsang le oscillator e inehetseng e tlaase-speed on-chip) A/D converter · 8/10-bit resolution A/D converter (VDD = 1.6 ho 5.5 V) Kenyelletso ea Analog: 6 ho likanale tsa 26 · Voltage ea ka hare ea litšupiso (1.45 V) le sensor ea mocheso Hlokomela 1 I/O port · I/O port · I/O port: 16 to 120 (N-ch open drain I/O [ho mamella voltage ea 6 V]: 0 ho isa ho 4, N-ch open drain I/O [VDD standstand voltage Note 2/EVDD withstand voltage Note 3]: 5 to 25) · E ka hlophisoa ho N-ch open drain, TTL input buffer, on-chip pull-up resistor · Sehokelo se fapaneng se ka bang teng. : E ka hokela sesebelisoa sa 1.8/2.5/3 V · On-chip key interrupt function · On-chip clock output/ buzzer output controller Ba bang · On-chip BCD (binary-coded decimal) correction circuit Notes 1. E ka khethoa feela ka HS (high-speed main) mode 2. Lihlahisoa tse nang le 20 ho isa ho 52 pins 3. Lihlahisoa tse nang le 64 ho isa ho 128 pin
